8 Channel RC Servo Driver Over RF Link using NRF24L01 RF Module – Arduino Compatible

Rajkumar Sharma
1.110 Views
moderate
Tested
SKU: EL112382
Quote Now
0 Likes

This is an easy-to-build open-source Arduino compatible board that enables driving 8 RC servos over NRF24L01 RF Link. The project can be used as a standalone RC servo driver or 8 channel RF remote-controlled RC servo Receiver. An optional OLED display option can be used to develop RC signal monitor. The tiny module contains an ATmega328 microcontroller, connectors for 8 x Servo interface, DC supply connector, bulk electrolytic capacitor C5 on DC supply to provide jitter-free smooth movement of RC servos. Operating Supply 5V DC.

This board is compatible with our Dual Joystick RF Remote Transmitter with NRF24L01 RF module or Single Joystick Remote Control Transmitter using NRF24L01 as the transmitter. The user will be able to drive 4 RC servos or 2 RC servos with these transmitters respectively.

Applications

8 Channel RC Servo Controller
RF Remote Controlled 8 Channel RC Servo Receiver and Controller
RC Signal Monitor Reader
3 Channel PWM Output Over NRF24L01 RF Link (Arduino Digital Pin D3, D5, D6)

Code

A new Atmega328 microcontroller requires a bootloader and Arduino code. Connector CN4 is provided to do needful, the bellow link will help you to learn more about programming and boot-loader burning.

https://www.arduino.cc/en/Tutorial/BuiltInExamples/ArduinoToBreadboard/

Arduino Code is available below as a download for both RX and TX. A compatible transmitter board is published here. This is Arduino compatible hardware. User may write their own code using Arduino IDE. Code can be uploaded to the board using the CN4 programming connector following the connection diagram below.

Arduino Pin Configuration

RC Servo 1 to 8: A5, A4, D2, D3, D4, D5
NRF24L01: CE>D9, CSN>D10, D11>MOSI, D12>MISO, D13>SCK
OPTIONAL 0.96INCH OLED DISPLAY: A4 AND A5, In the Case of OLED display, is in use, you can only use 6 channel RC servo outputs.
LED D2: FUNCTION LED >A0

Hardware Details

CN1: OLED Display Connector (Optional) Can be used as RC signal monitor
U1: Atmega328 Micro-Controller
D1: Power LED
D2: Optional Function LED connected to A0 Analog pin of Arduino
CN7: DC Supply Input 5V DC
CN4: Arduino Programming Connector (Boot-Loader and Arduino IDE)
CN2: NRF24L01 RF Trans-receiver Module for RF Link
U2: 3.3V Regulator which power NRF24L01 Module
PCB Dimensions: 44.45 x 37.94 mm

Schematic

Parts List

NO	QNTY.	REF.	DESC.	MANUFACTURER	SUPPLIER	SUPPLIER PART NO
1	1	CN1	4 PIN MALE HEADER PITCH 2.54MM	WURTH	DIGIKEY	732-5317-ND
2	1	CN2	NRF24L01 RF MODULE	SEED STUDIO	ALIEXPRESS
3	4	CN3,CN4,CN5,CN6	8 PIN MALE HEADER PITCH 2.54MM	WURTH	DIGIKEY	732-5321-ND
4	1	CN7	2 PIN SCREW TERMINAL PITCH 5.08MM	PHOENINX	DIGIKEY	277-1247-ND
5	2	C6,C9	10uF/25V SMD SIZE 1206	MURATA/YAGEO	DIGIKEY
6	3	C2,C3,C4	0.1uF/50V SMD SIZE 0805	MURATA/YAGEO	DIGIKEY
7	1	C5	470uF/25V	PANASONIC	DIGIKEY	PCE4009CT-ND
8	2	C7,C8	22PF/50V SMD SIZE 0805	MURATA/YAGEO	DIGIKEY
9	2	D1,D2	LED SMD SIZE 0805	OSRAM	DIGIKEY	475-1278-1-ND
10	1	D3	1N4007	DIODE INCO.	DIGIKEY	S1MBDITR-ND
11	1	R1	10K 5% SMD SIZE 0805	MURATA/YAGEO	DIGIKEY
12	2	R2,R3	1K 5% SMD SIZE 0805	MURATA/YAGEO	DIGIKEY
13	1	R4	1M 5% SMD SIZE 0805	MURATA/YAGEO	DIGIKEY
14	1	U1	ATMEGA328TQPF-32	MICROCHIP	DIGIKEY	ATMEGA328PB-AURCT-ND
15	1	U2	LM117-3.3V	TI	DIGIKEY	LM1117MP-3.3/NOPBCT-ND
16	1	X1	16Mhz	ECS INC	DIGIKEY	X1103-ND
18	1	C1	1uf/25V SMD SIZE 0805	MURATA/YAGEO	DIGIKEY